Well water in Walpole, New Hampshire
In Walpole, none of 37 private wells tested between 2006 and 2020 had fluoride above the New Hampshire guidance level (4 mg/L), according to NH DHHS.
37 private wells tested 2006 to 2020 in state summaries. Data refreshed .
Separately, a USGS and NHDES statistical model puts the chance that a bedrock well in Walpole exceeds 5 ug/L of arsenic at 8% (as low as 1% in parts of town), based on geology rather than tests.
What homeowner tests found
NH DHHS WISDOM private well summaries: private wells tested and reported to the state, 2006 to 2020. Shares are against the level the state applies to each contaminant, named in the last column; several are stricter than EPA.
| Contaminant | Wells tested | Above state level | Median | 95th pct | Highest | State level | |
|---|---|---|---|---|---|---|---|
| Fluoride | 37 | 0% | 0.3 | 1.2 | 2.6 | 4 mg/L |
Get the free Walpole well report
One email with the numbers above, what they mean for a home in Walpole, exactly which tests to order, and what treatment fits the local profile. No spam, unsubscribe in one click.
What this means
Among homeowners in Walpole who sent a sample to the state lab, no health-based limit was exceeded often enough to publish a share. That is good news, but a single well can still be the exception.
What to test for in Walpole
- Volatile organic compounds (VOCs)8 leaking underground storage tank sites on record locally.
- PFAS1 unlined landfill on record locally.
- Metals panel3 hazardous waste sites on record locally.
- Coliform bacteriaRecommended for every private well, every year.
- NitrateRecommended for every private well, especially near farms or septic systems.
Wells in Walpole
160 domestic wells in Walpole are on record with the state since 1984. 100% are drilled into bedrock, and the typical well is 402 feet deep (one in ten goes past 600 feet).
In a typical Walpole well, bedrock starts about 13 feet down, the median yield is 3.5 gallons per minute, 40% of wells yield under 3 gallons per minute and usually need a storage tank.
Bedrock wells are where arsenic, uranium and radon come from: the water sits in fractures in granite and metamorphic rock and picks up whatever the rock carries. That is why testing for those three matters more here than in a dug or gravel well.
Find your own well's report
The state keeps the driller's report for most wells drilled since 1984. It tells you how deep your well is, where bedrock starts, and how much water it makes, which decides what treatment can work.
- Open NHDES OneStop and choose Water Well.
- Enter your town and one word of your street name. Leave out the house number and the Road or Street part; a short search matches more.
- In the results, click Show for your address to see the report: total depth, depth to bedrock, casing, yield in gallons per minute, static water level, and the driller.
- Save Results exports the whole list to a spreadsheet.
Reports exist only for wells drilled since January 1984, when reporting became mandatory, and street names are as they were when the well was drilled.
Contamination sources on record in Walpole
NHDES records 8 leaking underground storage tank sites, 1 unlined landfill, 3 hazardous waste sites, and 3 reported spills and releases in Walpole, among 83 regulated sites in total. Groundwater does not follow property lines, so a well within a few hundred feet of one of these is worth testing for what that site could release.
- 8
- leaking underground storage tank sitesGasoline and heating oil that leaked from tanks move through groundwater as benzene, MTBE and other volatile organic compounds.
- 1
- unlined landfillOlder unlined landfills are a leading source of PFAS, VOCs and metals in nearby wells.
- 3
- hazardous waste sitesSolvents, degreasers and metals from industrial sites can travel far in fractured bedrock.
- 3
- reported spills and releasesMost spills are fuel; a few are solvents or chemicals that reach the water table.
- 22
- registered underground storage tank sitesRegistered tanks are regulated and inspected; they matter most when they are old or near a shallow well.
- 13
- locally identified potential contamination sourcesTowns inventory these (vehicle repair, labs, salt piles, farms) when they draw wellhead protection maps.
- 30
- other remediation projects
- 3
- other solid waste facilities
Book a free water test in Walpole
A licensed local water treatment company tests your tap water in your home, walks you through the numbers, and quotes treatment only if something needs fixing. Free, about 30 minutes, no obligation.
Common questions
How deep are wells in Walpole?
The typical domestic well in Walpole is 402 feet deep, based on 160 wells reported to the state since 1984. One in ten is deeper than 600 feet. 100% are drilled into bedrock.
How often should I test a private well in Walpole?
Test for bacteria and nitrate every year. Test once for arsenic, uranium, radon, fluoride, manganese and PFAS, then again every three to five years or after any change in taste, color, or plumbing.
Sources
- NH DHHS WISDOM private well summaries: summaries for 1 contaminants in Walpole, up to 37 wells each. Town summaries of private well tests run by the New Hampshire Public Health Laboratories, published by NH DHHS through the WISDOM environmental public health tracking portal. Exceedance shares use New Hampshire guidance levels, which are stricter than EPA for arsenic (5 ug/L), manganese (0.3 mg/L), radon (2,000 pCi/L) and sodium (20 mg/L). Statistics for small counts are suppressed (*). Retrieved September 3, 2026.
- NHDES Water Well Inventory: 195 well records in Walpole, 160 domestic. Well construction records reported to the New Hampshire Department of Environmental Services Water Well Board. Only aggregates are shown; owner names and addresses are never stored. Retrieved September 3, 2026.
- NHDES OneStop regulated sites: 83 regulated sites located in Walpole. Remediation sites, underground storage tanks, solid waste facilities and potential contamination sources from the New Hampshire Department of Environmental Services OneStop database. Retrieved September 3, 2026.
Non-detects count as samples and are treated as zero when computing medians. Exactly at the limit counts as not above it. A sample belongs to the town containing the well's reported coordinates.